Uniden BCD996XT Firmware Revision Notes 1.07.03

Contents

Installation Steps

Here is what you need to do to apply the 1.07.03 update.

1. Download the latest version of BC_VUP3 (the firmware update tool) by clicking BC_VUP_V3_03_00.zip.
2. Unzip the files you downloaded in Step 1 to your desktop. Then run setup.exe to install the firmware updater. (If you previously installed a version of BC_VUP, be sure you delete the old install files before reinstalling. These files are in a "BCSS" directory.)
3. Run the BC_VUP3 application you installed in Step 2. Follow all on-screen instructions, selecting the BCD996XT to update and the V1_07_03 version.

• All updates are cumulative. Applying the latest update includes all changes made by previous updates, too.
• Most update problems are caused by serial port issues. See the troubleshooting hints in the Update Troubleshooting section if you have problems.
• Two great forums exist for sharing information about this scanner within the user community:
  • The RadioReference forums ( http://www.RadioReference.com/forums)
  • The BCD996XT Yahoo! Group (http://groups.yahoo.com/group/BCD996XT)

What is Changed by This Update?

Previous Updates

v1.06.00

To adjust the auto decode threshold limit, start with the scanner powered off. Then, follow these steps:

1. While holding down the HOLD button, power on the scanner.
2. Access the hidden P25 Adjust Mode menu by MENU --> Settings --> P25 Adjust Mode.
3. Set the mode to 11, which is the optimal setting for most P25 systems. Some systems are reported to decode better at a setting of 8.
4. If you have previously adjusted the P25 Adjust Level, reset it to a value of 50 by MENU --> Settings --> P25 Adjust Level.

v1.04.00

This update makes the following changes to your BCD996XT scanner:

• Add support for storing Unit IDs in channels with alpha tags.
• Fixed a problem where corrupted memory caused by a bad PC programming upload would make the scanner lock up on the copyright screen.
• Save Hold status immediately instead of at power-down.
• Add ATT indication in Close Call Only mode
• Fixed a bug that could cause APCO P25 decoding to stop in some conditions.

Using the Unit ID Feature

The Unit ID (UID) feature lets you see the unit ID of the radio currently transmitting on Motorola, EDACS, and APCO P25 systems. To see the Unit ID, you need to first turn on the global Unit ID option in the Settings menu.

1. Press MENU.
2. Scroll to SETTINGS and press E/yes.
3. Scroll to Disp. Unit ID and press E/yes.
4. Scroll to On and press E/yes.

If you program a Unit ID into a channel, you can assign an Alpha to the Unit ID. You program a Unit ID just like an iCall ID (press ./no then the Unit ID).

Notes:

• In some cases where you catch a transmission already in progress you will not see the Unit ID.
• In some cases where a second party responds to a transmission before the channel is released, you will not see the second party's Unit ID and will continue to see the first party's Unit ID.

Update Troubleshooting

Follow these tips to troubleshoot any update problem you encounter:

• When prompted, be sure to turn off the scanner and hold down both the L/O and 6 buttons while turning power on. The backlight should come on and remain on until the end of the update.
• If an error occurs during the update, simply repeat all steps, including turning off power, holding down L/O and 6, and turning power back on. Even if the backlight is already on, you need to repeat this step if you restart the update.
• Almost all update error messages or faults that result in the scanner powering up with a blank display the the backlight on after the update are caused by:
  • Incorrect COM port selection: Be sure you have selected the COM port that the scanner is plugged into.
  • COM port software conflicts: No other software can be running that uses the COM port. Be sure to close any running scanner control software. Also, if you have ever used a PDA with this PC, there is probably synchronization software running all the time that takes over the COM port. You can usually stop that software by right-clicking on its icon in the lower right side of your PC screen, then selecting "Quit" or "Exit."
    
    If your PC does not have a COM port, you can use a USB-->RS232 adapter. Uniden sells such an adapter specifically for this scanner (Model USB-1). Or, you can use many other adapters that are available at computer retailers. Note that some adapters do not work, or require updated drivers. Uniden only supports the USB-1.
  • Interruption during the update.
• For all of the above conditions, you can restore normal scanner operation only by successfully applying the update. Restart the update from the beginning and ensure that you've followed all steps correctly.

Revised Protocol

This protocol document revises and replaces the protocol published in The Complete Reference.

BCD996XT_v1.04.00_Protocol.pdf