Hold mode

This page applies only to the BCD996XT. For other models see:

Hold mode lets you edit the current frequency, system, site, or channel. You can access these functions by using the different key operations:

Key Operation in Hold Mode

Key Name

(2nd operation)

Action On

BCD996XTkeysPri.png

PRIORITY

keys1.png

1 (Search 1)

keys2.png

2 (Search 2)

keys3.png

3 (Search 3)

Tap Toggle priority mode. Enter the digit in Direct Entry.
FUNCTION + Tap Toggle priority mode. Start the search range assigned to this Search Key.
Key Name

(2nd operation)

Action on:

BCD996XTkeysWx.png

Weather

keys4.png

4 (IF exchange)

keys5.png

5 (Level offset)

keys6.png

6 (Display mode)

Tap Toggle Weather Priority Mode Enter the digit in Direct Entry.
FUNCTION + Tap Toggle Weather Priority Mode Toggle the IF for that the current frequency. Change the volume offset for the current channel. Change the display mode.
Press & Hold Go to Weather Scan mode. NA NA NA
Key Name

(2nd operation)

Action on:

BCD996XTkeysGPS.png

GPS

keys7.png

7 (Attenuation)

keys8.png

8 (Reverse freq.)

keys9.png

9 (Modulation)

Tap Switch to the GPS Navigation display. Enter the digit in Direct Entry.
FUNCTION + Tap Switch to the GPS Navigation display. Toggle the attenuator state. NA Change the modulation.
FUNCTION + Press & hold NA Toggle the attenuator state for all signals. If on a channel that has a valid reverse (input) frequency, show the repeater reverse frequency for the current frequency (the scanner returns to the original frequency when you release the key). NA
Key Name

(2nd operation)

Action on:

keysMenu.png

Menu

keysNo.png

. / No (Decimal)

keys0.png

0

keysYes.png

Yes (Enter)

Tap

Enter the Menu Mode.

If you've entered a system number tag/channel number tag in Direct Entry, go to the specified system and channel.

Enter a decimal point, hyphen, or "i" for Direct Entry. Enter 0 in Direct Entry. Go to edit mode for the current channel or, if set to a trunked system frequency go go the edit mode for the system.
FUNCTION + Tap Enter the Menu for the current system or search range. NA NA NA
Key Name

(2nd operation)

Action on:

BCD996XTkeysSq.png

SQUELCH

BCD996XTkeysVol.png

VOLUME

keysScan.png

SCAN/SEARCH

keysHold.png

HOLD/RESUME

Rotate Adjust Squelch. Adjust volume. Turn fully counterclockwise past click to turn off scanner. NA NA
Tap Change Close Call mode. Change backlight level. Resume scanning. Resume scanning.
Press & Hold Go to Close Call Only mode. NA NA

Hold on the current system and resume scanning.

FUNCTION + Tap Go to Tone-Out Mode. Go to P25 status mode. Go to the Quick Search prompt. NA

Key Name

(2nd operation)

Action on:

keysLO.png

LOCKOUT

keysScrollFunc.png

SCROLL - FUNCTION

Rotate NA

Scroll through channels.

Function + Rotate NA Scroll through systems.
Tap Temporary lockout the current channel. If the current channel is temporarily or permanently locked out, unlock it. Activate the FUNCTION mode for the next keypress.
Function + Tap Temporarily lockout the current system. If the current system is temporarily or permanently locked out, unlock it. NA
Double Tap Permanently lockout the current channel. NA
Function + Double Tap Permanently lockout the current system. NA
Press & Hold Unlock all channels in the current system. "Latch" the FUNCTION mode. Scanner stays on the current system and all keypresses use the FUNCTION mode until you tap the control again.
Function + Press & Hold Prompt to Unlock All Systems (Y/N)? If you press E/Yes the scanner unlocks and enables all systems, sites, and searches. NA

Reading the displays in Hold mode

The display information in Hold mode varies depending on the type of system the scanner is Holding on.

Conventional system display

When the scanner is holding on a conventional system, it displays the following screens: BCD396XTholdConvCallouts.png

Trunked system display

BCD396XTholdTrunkedCallouts.png

Service search with scan hold display

BCD396XTholdSearchCallouts.png

This page applies to the following scanner(s): BCD996XT Users Guide